MENU
STANDARD OPERATING PROCEDURE Pedestal Grinder DO NOT use this machine unless you have been trained and assessed to a competent level in its safe use and operation, and have been given permission to use this equipment. Face shield must be worn at all times when grinding. Long and loose hair must be contained when operating this equipment.
7.4 Operation Safety – Allow the grinder to "run up" to operating speed before applying it to the job. – Never bump the grinder on to the job, or let the disc hit any other object while grinding. – Keep the grinding disc at a 15 to 30 degree angle to the work. – Make sure the work piece is held firmly in a bench vice, where necessary.
Operating Procedure 1. Inspection Before using the polisher/grinder inspect it and its surroundings for the following: C Make sure the electric power connections are made correctly and that the power cable is not damaged. C Make sure the polisher/grinder, including the wheel and the bowl, are clean. C Make sure the table and the floor around the table are clean and dry.
1910.211 (a) (1) "Point of operations" means that point at which cutting, shaping, boring, or forming is accomplished upon the stock. 1910.211 (a) (2) "Push stick" means a narrow strip of wood or other soft material with a notch cut into one end and which is used to push short pieces of material through saws.
Standard Number: 1926.303 Title: Abrasive wheels and tools. GPO Source: e-CFR. 1926.303(a) Power. All grinding machines shall be supplied with sufficient power to maintain the spindle speed at safe levels under all conditions of normal operation. 1926.303(b) ...
The milder abrasives like 32 and 38 Aluminum Oxide are best for lighter precision grinding operations on steels and semisteels, while the intermediate 57 and 19 Aluminum Oxide abrasives are used for precision and semiprecision grinding of both mild and hard steels. The severity of the grinding operation also influences the choice of grade.
the grinder was running at an appropriate speed within the grinding wheel tolerance, and issues involving machine guarding and other adjustments to the machine. ... operation (the working portion of the blade between the two guides). Band saw wheels must be fully encased. Make sure the saw includes a tension-control
STANDARD OPERATING PROCEDURE . Grinding solid samples for IRMS . 1. METHOD OBJECTIVE: To prepare solid samples for isotope and elemental analysis by grinding. 2. METHOD VARIATIONS: Due to the variety of sample types, variation in the conditions of analysis may require modifications to the method used for different samples. Samples with
grinder from the wall receptacle. • If the grinder is hardwired into a box, Lock-out/Tag-out. • Be alert and cautious when a grinding operation requires locating fingers close to the wheel. • Feed the stock into the wheel with light to medium pressure. Do not force the piece. • Do not use the side of the grinding wheel to shape stock.
Wear goggles for all grinding machine operations. Check grinding wheels for cracks (Ring Test Figure 5-11) before mounting. Never operate grinding wheels at speeds in excess of the recommended speed. Never adjust the workpiece or work mounting devices when the machine is operating Do not exceed recommended depth of cut for the grinding wheel or ...
Standard Operating Procedure Title:_SOP-005 Bench Grinder PI: Art Erdman Lab Location: Mayo G217 Issue Date: 7/8/13 Revision Date: NA Prepared by: Marlina Komarek Approved by: Hazard Identification: Physical Danger Exposure Assessment: Motions Rotating Motion In bench grinder operation, the grinding wheel is a source of rotating motion.
grinding disc. Never make adjustments while the angle grinder is running. Do not switch off the angle grinder when it is under load, except in an emergency. Allow angle grinder to reach operating speed before applying to work piece & increase load gradually. Do not lift or drag angle grinders by the cord.
Grinding Process Grinding is a surface finishing operation where very thin layer of material is removed in the form of dust particles. Thickness of material removed is in range of 0.25 to 0.50 mm. Tool used is a abrasive wheel Grinding machine is a power operated machine tool where, the work piece is fed
STANDARD OPERATING PROCEDURE . Grinding solid samples for IRMS . 1. METHOD OBJECTIVE: To prepare solid samples for isotope and elemental analysis by grinding. 2. METHOD VARIATIONS: Due to the variety of sample types, variation in the conditions of analysis may require modifications to the method used for different samples. Samples with
4.0 Procedures 4.1 Do not allow wet sawing, grinding, and drilling/coring to entgenerated wastewater er storm drains or watercourses without first being filtered. In addition, the sediment shall not be allowed to remain on the pavement after the operation has ceased.
